JDE in Partnership with West electronics latest design ECU version 6.0
Now From JDE A first no other manufacture offer's a brushless starter ECU
IF you have had a starter motor fail because of brush failure or barely enough RPM
to get you turbine started and wished you could use a brushless starter motor the wait is over
JDE has available now a DECU for use with a brushless starter motor with these motor's your engine can be spooled up effortlessly to as high as 30.000 + rpm's depending on your choice of brushless motor's and matching speed control
Standard DECU for the brushed starter motor's includes Data panel, main unit, magnetic Hall sensor, ,DVD setup manual,
price = $ 450.00 +S&H
New brushless starter DECU includes the above for use with brush less starter motor
price = $ 500.00 +S&H
items not included brushless motor and speed control for brushless motor operation, temp probe and solenoids sold separately
JDE Hawk series of turbine engine's
The JDE Turbine assembled and kit Engine's now completely
manufactured in the USA
JDE Turbine wheel's and NGV's areo space cast in the USA
break down of kit engine shown below part's may defer from those shown.

All kit parts are drilled and tapped ready for assembly
H-12 thrust kit complete with fitting's, line's, pump with manual start ECU with data terminal
$=1780.00 +S&H
H-12 Auto Start 12 LB kit complete as above with auto start ECU & data terminal and gas solenoid
$1880.00+S&H
Spec.'s for kit engine's 7" in length and 3.5 " in dia
weight 1lb 12 oz's engine only
__________________________________________________________________
H-12
Assembled and test run engine air start complete ready to run with engine mount
$1995.00+S&H
H-12
Assembled and test run engine with auto start complete ready to run with engine mount and gas solenoid
$2195.00+S&H
Assembled engine specs for above 12+ LB thrust 7" in length 3.5" in dia weight same as above engine only
H-14
assembled 14 + LB thrust engine with auto start $2350.00
----------------------------------------------------------------------------------------------------------------
Available Parts
The parts listed below fit many of the existing 12 LB
thrust engine's (call with your specific needs)
Note - all Items are drilled & taped unless specified
|
Item No. |
Description |
Price |
Per |
|
1 |
Compressor nut |
$10.50 |
1 |
|
2 |
Front spacer |
$10.75 |
1 |
|
3 |
Compressor (446335-10) |
$155.00 |
1 |
|
4 |
Intake |
$38.50 |
1 |
|
5 |
Shaft seal |
$24.65 |
1 |
|
6 |
Case front |
$28.95 |
1 |
|
7+8 |
Diffuser + filter |
$155.00 |
1 |
|
8 |
Filter screen |
$1.75 |
1 |
|
9 |
Filter cover |
$6.75 |
1 |
|
10 |
Pre-load Spring |
$10.50 |
1 |
|
11 |
Bearing Tunnel |
$45.95 |
1 |
|
12+1+27 |
Shaft + nuts |
$75.50 |
Set |
|
14+16+17+19 |
Combustion chamber case - ends flanged, inner/outer flat |
$75.75 |
Set |
|
15 |
Glow Plug boss (2 off) |
$21.50 |
Ea. |
|
18 |
Vaporizer tube (12) inconnel |
$95.50 |
12 |
|
Part of item 20 |
Needles for fuel injectors (12 + spares) |
$25.00 |
|
|
21 |
Case outer housing rolled |
$18.50 |
1 |
|
22 |
Case rear - machined |
$28.95 |
1 |
|
23 |
turbine wheel cast bored to 4 MM requires finishing 56 MM |
$Call |
|
|
24 |
Turbine Wheel- cast, bored and faced (requires balancing)ground to 55MM |
$265.00 |
1 |
|
25 |
New CNC starter system as shown on the front page engine Includes motor and bendix |
$60.00 |
1 |
|
26 |
Rear spacer |
$10.50 |
1 |
|
27 |
Turbine nut |
$10.95 |
1 |
|
29 |
2 piece Exhaust cone |
$35.00 |
1 |
|
30 |
Single piece cone |
$35.00 |
|
|
35 |
NGV machined |
$250.00 |
1 |
|
38 |
Pre load tube short or long specify when ordering |
$8.50 |
1 |
|
39 |
Swirl jet (6 off)original style combustor |
$26.95 |
6 |
|
40 |
Ceramic ball bearing (2 required) |
$95.95 |
EA. |
|
41,42,43,44,49 |
Complete set of screws (ASE) |
$21.56 |
Set |
|
45 (2 off) + 50 |
O ring set |
$6.95 |
Set |
|
|
Festo connectors - 3mm (female) |
$7.50 |
Ea. |
|
|
Festo fuel tube - 3mm |
$3.75 |
Per ft |
|
NEW JDE fuel pump |
JDE Fuel pump -12 |
$ 125.00 |
1 |
|
|
Festo fuel tube - 4mm |
$4.75 |
Per ft |
|
|
Set of drawings 54 turbine |
$35.00 |
1 |
|
|
Turbine for gas generator - machined |
call |
1 |
|
|
temp probe with connector |
$50.00 |
+S&H |
|
|
Solenoid valve /Brass style |
$60.00 |
|
|
66 MM turbine wheel bored face & sized requires balancing | $ 250.00 | |
| 66 MM NGV Machined | $ 250.000 | |
| 66 MM Bearings ceramic bearings | $ 95.95 Ea. |
| NEW | Diffuser KJ -style or Ram style | $ 135.00 |
| NEW | bearing tunnel for KJ or Ram | $ 65.00 |
All Prices + S&H
all sales are final no returns
prices subject to change with out notice. JDME LLC